Supervisor Operations

IntelliSight Processor Setup

To configure the IntelliSight processor, do the following. 1. Start the Supervisor. 2. On the Home screen, click the device icon for the IntelliSight processor to be configured. The following appears.
If cameras were already discovered, an image of all setup cameras will appear if the cameras are connected and online; one in each of the four quadrants of the image area. The order of appearance is deteremined by the order in which the cameras were added. The first camera will display in the upper left; second in the upper right; third in lower left; and fourth in lower right. If needed, use the video controls to refresh the images. 3. In the Navigation section, click Device Settings. The following appears.
User Descriptions 4. Enter descriptions for each field as needed. The description entered for the first field is what appears as the Device Name in the other Supervisor screens. Feature Licensing 5. If you received a new license file from Image Sensing Systems, click OPEN and select File. Next, click the send button and your system will reboot with the new license loaded. Time 6. For Time Source, select the method to be used to synchronize the clock in the IntelliSight processor.
  • Manual - Select to synchronize the clock to the connected computer. After applying the changes, you must click SET TIME in the Commands section of the Device or Home screen.
  • TS2 - Not applicable
  • NTP - Select if the clock is to be synchronized with an NTP server. Enter the URL or IP address of the NTP time server to be used and click ADD. At least one (and up to five (5)) NTP servers must be added. If more than one NTP server is entered, the first is used as the primary. If, for some reason, the server cannot be contacted, the second will be tried, and so on. To delete a time server from the list, select it and click DELETE.
NOTE: If a URL is entered instead of an IP address, the DNS fields in the Network section must be filled in. 7. For Time Zone, select the time zone where the IntelliSight processor is installed. Network 8. Only the WAN interface is user changeable. For the WAN interface, the addressing applies to the WAN connector; which is used to connect to a network outside of the Controller Cabinet, such as the Traffic Management Center (TMC). Enter the IP Address, Subnet Mask, and Default Gateway for the WAN Interface. NOTE: If port forwarding is used, the IntelliSight processor should be configured with a static IP address that is on the same network as the router/cell modem.
  • IP Address - Address to be used for the WAN network interface.
  • Subnet Mask - Subnet Mask to be used for the WAN network interface.
  • Default Gateway - Default Gateway to be used for the WAN network interface.
  • Primary DNS - Address of the primary DNS server. Only available for the WAN interface.
  • Secondary DNS - Address of the secondary DNS server. Only available for the WAN interface.
Video 9. Move the slider or enter a value from 100 to 5000 to set the rate, in kilobits per second, to be used when viewing video on the Device screen for the IntelliSight processor. The default is 2048 kbps. The bitrate has no effect on the static image (snapshot). It only has an effect when playing video, and it should be set according to what the viewing device or network can handle. NOTE: The value selected in this section only affects the bitrate of the Quad display. Individual sensor stream bitrates are set in their respective Device Settings page. Communication Ports 10. This area is used when the IntelliSight processor is connected to a router or cell modem and port forwarding is required.
  • For Communication Ports, select or enter the starting port number in the sequence to be used. The system requires two ports for the IntelliSight processor and two for each IntelliSight camera connected to the IntelliSight processor.
  • For RTSP Port, select or enter the port number to be used for video streaming (used for both the Supervisor and third party programs).
  • Communications and RTSP ports must be configured as part of the router/cell modem forwarding configuration. For additional information, see Port Forwarding.
Webserver 11. This area is used to set the port and set up a username and password for the webserver.
  • Port - Enter the port number used to access the webserver. Valid entries are 443, 8443, or a number between 41952 and 65535. The default is 443. If the port specified is already in use, a message will be posted to the Operations Log and the value will revert back to the last working port. NOTE: If port forwarding is used, the webserver port must be configured as part of the router/cell modem forwarding configuration.
  • Authentication - Select whether or not a username and password is required to access the webserver. If Enabled, enter the Username and Password. A maximum of 20 characters can be entered for each. The default username and password is admin/ISS12345
  • 12. Click APPLY CHANGES.
  • 13. If the Time Source selected is Manual, return to the Device screen and click SET TIME in the Commands section. 14. Return to the Home screen. 15. Configure the IntelliSight cameras connected to the IntelliSight processor. 16. Click APPLY CHANGES.
Version 4.5.0 - Copyright © 2025, Image Sensing Systems, Inc. All rights reserved.