Configuring IntelliSight Devices
Device Settings - IntelliSight Processor
Defines the operating parameters for the device.
User Descriptions - Enter descriptions for each field as needed. A maximum of 126 characters can be entered for each of the four fields. NOTE: The description entered in the first field is used as the name of the device.
Feature Licensing – If you received a new license file from Image Sensing Systems, press open and select file. Next, press the send button and your system will reboot with the new license loaded.
Time Source - Select the method to be used to synchronize the clock in the IntelliSight Processor.
Manual – Select to synchronize the clock to the connected computer. After applying changes, you must click SET TIME in the Commands section of the Device or Home screen.
TS2 – Select if the IntelliSight Processor’s clock is set by TS2 time set commands from a TS2 compatible controller. The IntelliSight Processor monitors the TS2 time every minute and if the difference between the two is greater than two seconds, the TS2 time is applied to the IntelliSight Processor.
NTP – Select if the clock is to be synchronized with an NTP server. Enter the URL or IP address of the NTP time server to be used and click ADD. At least one (and up to five) NTP servers must be added. If more than one NTP server is entered, the first is used as the primary. If for some reason the server cannot be contacted, the second will be tried and so on. To delete a time server from the list, select it and click DELETE.NOTE: If a URL is entered instead of an IP address, the DNS fields in the Network section must be filled in.
For Time Zone, select the time zone where the IntelliSight Processor is installed. The selected time zone is passed to each IntelliSight Camera connected to the IntelliSight Processor.
TS2 – Select if the IntelliSight Processor’s clock is set by TS2 time set commands from a TS2 compatible controller. The IntelliSight Processor monitors the TS2 time every minute and if the difference between the two is greater than two seconds, the TS2 time is applied to the IntelliSight Processor.
NTP – Select if the clock is to be synchronized with an NTP server. Enter the URL or IP address of the NTP time server to be used and click ADD. At least one (and up to five) NTP servers must be added. If more than one NTP server is entered, the first is used as the primary. If for some reason the server cannot be contacted, the second will be tried and so on. To delete a time server from the list, select it and click DELETE.NOTE: If a URL is entered instead of an IP address, the DNS fields in the Network section must be filled in.
For Time Zone, select the time zone where the IntelliSight Processor is installed. The selected time zone is passed to each IntelliSight Camera connected to the IntelliSight Processor.
Network - Select the module to which the other Network parameters apply.
Network - Only the WAN interface is user changable. For the WAN interface, the addressing applies to the WAN connector, which is used to connect to a network outside of the controller cabinet, such as the Traffic Management Center (TMC).
Enter the IP Address, Subnet Mask and Default Gateway for the WAN Interface.
NOTE: If port forwarding is used, the IntelliSight Processor should be configured with a static IP address that is on the same network as the router/cell modem. IP Address - Address to be used for the WAN network interface.Subnet Mask - Subnet Mask to be used for the WAN network interface.Default Gateway - Default Gateway to be used for the WAN network interface.
Enter the IP Address, Subnet Mask and Default Gateway for the WAN Interface.
NOTE: If port forwarding is used, the IntelliSight Processor should be configured with a static IP address that is on the same network as the router/cell modem. IP Address - Address to be used for the WAN network interface.Subnet Mask - Subnet Mask to be used for the WAN network interface.Default Gateway - Default Gateway to be used for the WAN network interface.
Video - Move the slider or enter a value from 100 to 5000 to set the rate, in kilobits per second, to be used when viewing video on the Device screen.
The bitrate has no effect on the static image (snapshot). It only has an affect when playing video and it should be set according to what the viewing device or network can handle.
To set the value back to the default (2048), click Reset.
NOTE: The value selected for individual sensors on their respective Device Settings screens has no effect on the quad video display for the IntelliSight Processor.
Version 4.1 - Copyright © 2022, Image Sensing Systems, Inc. All rights reserved.